TU U 23.9-32944149-013:2024
Roll roofing and waterproofing material
Product Description and Scope of Application
HYDROBASE LIGHT consists of a base made of fiberglass or polyester fabric or a combined base, coated on both sides with bituminous binder, with protective layers on top in the form of coarse-grained granules or polymer film and on the bottom in the form of polymer film. The materials are manufactured for torch-on application.
Depending on the type of protective layers and area of application, the following grades are available:
HYDROBASE LIGHT K – with coarse-grained granules on the face side and polymer film on the torch-on application side of the sheet; used for installation of the top layer of the roofing membrane;
HYDROBASE LIGHT P – with polymer film on the face and bottom sides of the sheet; used for installation of the bottom layers of the roofing membrane and waterproofing of building structures.
Transportation and Storage
Transportation is carried out by all types of transport in covered vehicles in accordance with the Cargo Transportation Rules applicable to the given type of transport. Throughout the entire storage period, the material must be protected from atmospheric precipitation. Rolls are stored vertically on pallets in a single row by height.
Packaging Information
The material is packaged in UV-stabilized film and supplied on pallets
Application Instructions
In accordance with SWEETONDALE Installation Instructions
Main characteristics
| Parameter name |
HYDROBASE LIGHT P |
HYDROBASE LIGHT K |
Test Method |
||
| Mass per unit area, kg/m²* |
2,5 |
3,5 |
EN 1849-1 |
||
| Watertightness at 2 kPa pressure for 24 hours |
– |
– |
EN 1928 |
||
| Watertightness at 60 kPa pressure for 24 hours |
No water penetration |
No water penetration |
EN 1928 |
||
| Tensile strength along / across the sheet, N, not less than for material:
on fiberglass fabric on polyester fabric |
294/- 343/- |
294/- 343/- |
DSTU B V.2.7-83 |
||
| Flexibility on a bar with a radius of (25.0±0.2) mm at temperature, °C, maximum |
0 |
0 |
DSTU B V.2.7-83 |
||
| Flow resistance at elevated temperature, °C |
≥80 |
≥80 |
EN 1110 |
||
| Loss of coarse-grained surfacing, g/sample, maximum |
– |
3 |
DSTU B V.2.7-83 |
||
| Reaction to fire | Class E | DSTU EN 13501-1 | |||
| Type of protective coating: |
|
|
|||
| top side
torch-on side |
film without logo film without logo |
slate film without logo |
|
||
| Length/width, m |
15×1 |
10×1 |
|||
| Pallet packaging |
white heat-shrink bag with logo |
||||
* – deviation from the nominal value of 1 m² mass shall not exceed ±0.25 kg
TU U 23.9-32944149-013:2024
Roll roofing and waterproofing material
Product Description and Scope of Application
HYDROBASE STANDARD consists of a base made of fiberglass or polyester fabric or a combined base, coated on both sides with bituminous binder, with protective layers on top in the form of coarse-grained granules or polymer film and on the bottom in the form of polymer film. The materials are manufactured for torch-on application.
Depending on the type of protective layers and area of application, the following grades are available:
HYDROBASE STANDARD K – with coarse-grained granules on the face side and polymer film on the torch-on application side of the sheet; used for installation of the top layer of the roofing membrane;
HYDROBASE STANDARD P – with polymer film on the face and bottom sides of the sheet; used for installation of the bottom layers of the roofing membrane and waterproofing of building structures
Transportation and Storage
Transportation is carried out by all types of transport in covered vehicles in accordance with the Cargo Transportation Rules applicable to the given type of transport. Throughout the entire storage period, the material must be protected from atmospheric precipitation. Rolls are stored vertically on pallets in a single row by height.
Packaging Information
The material is packaged in UV-stabilized film and supplied on pallets
Application Instructions
In accordance with SWEETONDALE Installation Instructions
Main characteristics
| Parameter name |
HYDROBASE STANDARD P |
HYDROBASE STANDARD K |
Test Method |
||
| Mass per unit area, kg/m²* |
2,5 |
4,0 |
EN 1849-1 |
||
| Watertightness at 2 kPa pressure for 24 hours |
– |
– |
EN 1928 |
||
| Watertightness at 60 kPa pressure for 24 hours |
No water penetration |
No water penetration |
EN 1928 |
||
| Tensile strength along / across the sheet, N, not less than for material:
on fiberglass fabric on polyester fabric |
294/- 343/- |
294/- 343/- |
DSTU B V.2.7-83 |
||
| Flexibility on a bar with a radius of (25.0±0.2) mm at temperature, °C, maximum |
-10 |
-10 |
DSTU B V.2.7-83 |
||
| Flow resistance at elevated temperature, °C |
≥90 |
≥90 |
EN 1110 |
||
| Loss of coarse-grained surfacing, g/sample, maximum |
– |
2 |
DSTU B V.2.7-83 |
||
| Reaction to fire | Class E | DSTU EN 13501-1 | |||
| Type of protective coating: |
|
|
|||
| top side
torch-on side |
film without logo film without logo |
slate film without logo |
|
||
| Length/width, m |
15×1 |
10×1 |
|||
| Pallet packaging |
white heat-shrink bag with logo |
||||
* – deviation from the nominal value of 1 m² mass shall not exceed ±0.25 kg
TU U 23.9-32944149-013:2024
Roll roofing and waterproofing material
Product Description and Scope of Application
HYDROBASE ULTRA consists of a base made of fiberglass or polyester fabric or a combined base, coated on both sides with bitumen-polymer binder, with protective layers on top in the form of coarse-grained granules or polymer film and on the bottom in the form of polymer film. The materials are manufactured for torch-on application.
Depending on the type of protective layers and area of application, the following grades are available:
HYDROBASE ULTRA K – with coarse-grained granules on the face side and polymer film on the torch-on side of the sheet; used for installation of the top layer of the roofing membrane;
HYDROBASE ULTRA P – with polymer film on the face and bottom sides of the sheet; used for installation of lower layers of the roofing membrane and waterproofing of building structures, as well as for vapor barrier.
Transportation and Storage
Transportation is carried out by all types of transport in covered vehicles in accordance with the Cargo Transportation Rules applicable to the given type of transport. Throughout the entire storage period, the material must be protected from atmospheric precipitation. Rolls are stored vertically on pallets in a single row by height.
Packaging Information
The material is packaged in UV-stabilized film and supplied on pallets
Application Instructions
In accordance with SWEETONDALE Installation Instructions
Main characteristics
| Parameter name | HYDROBASE ULTRA P | HYDROBASE ULTRA K |
Test Method |
||
| Mass per unit area, kg/m²* |
3,0 |
4,0 |
EN 1849-1 |
||
|
3,5 ** |
4,5 ** |
||||
| Watertightness at 2 kPa pressure for 24 hours |
– |
No water penetration |
EN 1928 |
||
| Watertightness at 60 kPa pressure for 24 hours |
No water penetration |
– |
EN 1928 |
||
| Tensile strength along / across the sheet, N, not less than for material:
on fiberglass fabric on polyester fabric |
343/- 400/- |
343/- 400/- |
DSTU B V.2.7-83 |
||
| Flexibility on a bar with a radius of (25.0±0.2) mm at temperature, °C, maximum |
-15 |
-15 |
DSTU B V.2.7-83 |
||
| Flow resistance at elevated temperature, °C |
≥105 |
≥105 |
EN 1110 |
||
| Loss of coarse-grained surfacing, g/sample, maximum |
– |
1 |
DSTU B V.2.7-83 |
||
| Reaction to fire | Class E | DSTU EN13501-1 | |||
| Type of protective coating: |
|
|
|||
| top side
torch-on side |
film without logo film with logo |
slate film with logo |
|
||
| Length/width, m |
15×1 |
10×1 |
|||
| Pallet packaging |
white heat-shrink bag with logo |
||||
* – deviation from the nominal value of 1 m² mass shall not exceed ±0.25 kg
** – custom manufacturing is available upon request.
TU U V.2.7.-26.8-35492904-004:2010 with amendment 4
Rock mineral wool slabs
Product Description:
Fire Protection Slabs for Concrete Lamel are non-combustible, hydrophobized, thermal and sound insulation slabs made of mineral wool based on basalt group rocks.
Can be manufactured with aluminum foil or fiberglass coating.
Application:
In civil and industrial construction, during new construction and reconstruction of buildings and structures for various purposes, as fire protection and thermal insulation for reinforced concrete structures (reinforced concrete columns and floors). The boards are certified as the main element of the concrete fire protection system.
Application instructions:
Installation according to the Fire Protection Work Regulations “SD-FIRE PROTECTION Concrete fire protection system, consisting of mineral wool boards of the “Concrete Fire Protection Boards (MC, AF, SS, SP)” brand and anchoring metal elements (anchor+washer) HILTI IDMS”.
Storage:
Store in covered warehouses, preventing exposure to precipitation. During transportation, protect from damage and moisture.
Transportation:
Transportation must be carried out in accordance with the requirements of DBN G.1-4, DSTU B V.2.7-167. Products are shipped to the consumer no earlier than 24 hours after storage in the warehouse.
Packaging Information:
Polyethylene heat-shrink film is used for packaging.
Main physical and mechanical characteristics:
|
Parameter |
Unit of measurement |
Board Fire protection for concrete lamel |
Test Method |
| Density |
kg/m3 |
70-90 |
DSTU B V.2.7-38-95 |
| Thermal conductivity, λ25 |
W/mK |
0,037* |
DSTU B V.2.7-105-2000 |
| Thermal conductivity, λA |
W/mK |
0,041** |
DSTU B.V.2.7-182:2009 |
| Thermal conductivity, λB |
W/mK |
0,043** |
DSTU B.V.2.7-182:2009 |
| Compressive strength, not less than |
kPa |
50 |
DSTU B V.2.7-38-95 |
| Moisture content by mass, not more than |
% |
0,5 |
DSTU B V.2.7-38-95 |
| Organic matter content, not more than |
% |
3 |
DSTU B V.2.7-38-95 |
| Flammability |
degree |
NG |
DSTU B V.2.7-70-98 |
Geometric parameters:
|
Parameter |
Unit of measurement |
Value |
Test Method |
| Length |
mm |
1000 (±2%) |
DSTU B V.2.7-38-95 |
| Width |
mm |
200 (± 1.5%) |
DSTU B V.2.7-38-95 |
| Thickness (in 10 mm increments) |
mm |
60-150 in 10 mm increments (+ 3 mm; – 2 mm) |
DSTU B V.2.7-38-95 |
TU U V.2.7.-26.8-35492904-004:2010 (Amendment No. 4)
Non-combustible, hydrophobized mineral wool boards
Product Description:
Metal Fire Protection Board is a non-combustible, hydrophobized, thermal and sound insulation board made of mineral wool based on basalt group rocks.
Application:
In civil and industrial construction for new construction and reconstruction of buildings and structures of various purposes as thermal insulation and fire protection of metal structures.
To increase the fire resistance limit of load-bearing metal structures with a fire resistance limit from 60 to 180 minutes.
Certified in the metal fire protection system and the air duct fire protection system.
Application instructions:
Installation according to the Fire Protection Work Regulations “SD-FIRE PROTECTION Metal Fire Protection System” for cladding metal structures, consisting of mineral wool boards of the “Metal Fire Protection Boards (MC, AF, SS, SP)” brand and Ceresit CM 17 adhesive”, “SD-FIRE PROTECTION Air Ducts Fire Protection System” for cladding steel air ducts, consisting of mineral wool boards of the “Metal Fire Protection Boards (MC, AF, SS, SP)” brand and Ceresit CM 17 adhesive”.
Storage:
Store in covered warehouses, preventing exposure to precipitation. During transportation, protect from damage and moisture.
Transportation:
Transportation of boards must be carried out in accordance with the requirements of DBN G.1-4, DSTU B V.2.7-167. Products are shipped to the consumer no earlier than 24 hours after storage in the warehouse.
Packaging Information:
Polyethylene heat-shrink film is used for packaging.
Main physical and mechanical characteristics:
|
Parameter |
Unit of measurement |
Value |
Test Method |
| Density |
kg/m3 |
165 (±15) |
DSTU B V.2.7-38 |
| Thermal conductivity, *λ25 |
W/mK |
0,037 |
DSTU B V.2.7-105 |
| Thermal conductivity, **λA |
W/mK |
0,042 |
DSTU B.V.2.7-182 |
| Thermal conductivity, **ΛB |
W/mK |
0,045 |
DSTU B.V.2.7-182 |
| Compressive strength at 10% linear deformation, not less than |
kPa |
20 |
DSTU B V.2.7-38 |
| Moisture content by mass, not more than |
% |
0,5 |
DSTU B V.2.7-38 |
| Organic matter content, not more than |
% |
3 |
DSTU B V.2.7-38 |
| Flammability |
degree |
NG |
DSTU B V.2.7-70 |
*- according to protocol No. 56K/17;
**- according to protocol No. 94K/17.
Geometric parameters:
|
Parameter |
Unit of measurement |
Value |
| Length |
mm |
2400,1200 (±2%) |
| Width |
mm |
1000,600 (±1.5%) |
| Thickness |
mm |
30-70 in 10 mm increments (+3 mm; -2 mm) |
TU U V.2.7.-26.8-35492904-004:2010 (Amendment No. 4)
Rock mineral wool slabs
Product Description:
Fire Protection Door Slab is a non-combustible thermal and acoustic insulation slab made from rock mineral wool based on basalt group rocks.
Application:
Fire Protection Door Slabs are specially designed and intended for fire protection insulation of fire-rated doors and gates.
Application instructions:
Installation of slabs in the frame of fire-rated doors and gates as fire protection filler is carried out based on structural features in accordance with the technical documentation of the door and gate manufacturer.
Storage:
Store in covered warehouses, preventing exposure to precipitation. During transportation, protect from damage and moisture.
Transportation:
Transportation must be carried out in accordance with the requirements of DBN G.1-4, DSTU B V.2.7-167. Products are shipped to the consumer no earlier than 24 hours after storage in the warehouse.
Packaging Information:
Polyethylene heat-shrink film is used for packaging.
Main physical and mechanical characteristics:
|
Parameter |
Unit of measurement |
Fire Protection Door Slab 110 |
Fire Protection Door Slab 190 |
Test Method |
| Density |
kg/m3 |
100-120 |
170-200 |
DSTU B V.2.7-38-95 |
| Thermal conductivity λ25 |
W/mK |
0,037 |
0,038 |
DSTU B V.2.7-105-2000 |
| Compressive strength at 10% linear deformation, not less than |
kPa |
10 |
20 |
DSTU B V.2.7-38-95 |
| Moisture content by mass, not more than |
% |
0,5 |
0,5 |
DSTU B V.2.7-38-95 |
| Organic matter content, not more than |
% |
3,0 |
3,0 |
DSTU B V.2.7-38-95 |
| Flammability |
degree |
NG |
NG |
DSTU B V.2.7-70-98 |
Geometric parameters:
|
Parameter |
Unit of measurement |
Value |
Test Method |
| Length |
mm |
1000; 1200; 2000; 2400 (±2%) |
DSTU B V.2.7-38-95 |
| Width |
mm |
200, 600; 1000; 1200 (±1.5%) |
DSTU B V.2.7-38-95 |
| Thickness (in 10 mm increments) |
mm |
50-140 in 10 mm increments (+5 mm; -2 mm)*, 30-80 in 10 mm increments (+5 mm; -2 mm)** |
DSTU B V.2.7-38-95 |
*-for Fire Protection Door Slab 110;
**-for Fire Protection Door Slab 190.
TU U V.2.7.-26.8-35492904-004:2010 (Amendment No. 4)
Rock mineral wool slabs
Product Description:
Concrete Fire Protection Boards are non-combustible, hydrophobized, thermal and sound insulation boards made of mineral wool based on basalt group rocks.
Can be manufactured with aluminum foil or fiberglass coating.
Application:
The boards are intended for use in civil and industrial construction, in new construction and reconstruction of buildings and structures for various purposes as fire protection and thermal insulation of reinforced concrete structures (reinforced concrete columns and floors).
The boards are certified as the main element of the concrete fire protection system.
Application instructions:
Installation according to the Fire Protection Work Regulations “SD-FIRE PROTECTION Concrete fire protection system, consisting of mineral wool boards of the “Concrete Fire Protection Boards (MC, AF, SS, SP)” brand and anchoring metal elements (anchor+washer) HILTI IDMS”.
Storage:
Store in covered warehouses, preventing exposure to precipitation. During transportation, protect from damage and moisture.
Transportation:
Transportation must be carried out in accordance with the requirements of DBN G.1-4, DSTU B V.2.7-167. Products are shipped to the consumer no earlier than 24 hours after storage in the warehouse.
Packaging Information:
Polyethylene heat-shrink film is used for packaging.
Main physical and mechanical characteristics:
|
Parameter |
Unit of measurement |
Board Concrete Fire Protection 80 |
Test Method |
| Density |
kg/m3 |
70-90 |
DSTU B V.2.7-38-95 |
| Thermal conductivity, λ25 |
W/mK |
0,037* |
DSTU B V.2.7-105-2000 |
| Thermal conductivity, λA |
W/mK |
0,038** |
DSTU B.V.2.7-182:2009 |
| Thermal conductivity, λB |
W/mK |
0,040** |
DSTU B.V.2.7-182:2009 |
| Compressive strength at 10% linear deformation, not less than |
kPa |
10 |
DSTU B V.2.7-38-95 |
| Compressive strength, not less than |
kPa |
– |
DSTU B V.2.7-38-95 |
| Water absorption during partial immersion, not more than |
% |
10 |
DSTU B V.2.7-38-95 |
| Moisture content by mass, not more than |
% |
0,5 |
DSTU B V.2.7-38-95 |
| Organic matter content, not more than |
% |
3 |
DSTU B V.2.7-38-95 |
| Flammability |
degree |
NG |
DSTU B V.2.7-70-98 |
*-according to protocol No. 58K/17;
**-according to protocol No. 96K/17.
Geometric parameters:
|
Parameter |
Unit of measurement |
Value |
Test Method |
| Length |
mm |
1200 (± 2%) |
DSTU B V.2.7-38-95 |
| Width |
mm |
600 (± 1.5%) |
DSTU B V.2.7-38-95 |
| Thickness (in 10 mm increments) |
mm |
50-150 with 10 mm increments (+ 3 mm; – 2 mm) |
DSTU B V.2.7-38-95 |
Rigid Stone Wool Board
Product Description:
Technical insulation – rigid stone wool board. The boards are manufactured from mineral wool based on basalt group rock.
Can be produced laminated with reinforced aluminum foil or fiberglass cloth on one side. A significant difference between Technical Insulation boards and general construction insulation is the wide operating temperature range of the board.
Application:
Designed for thermal insulation of air ducts, gas ducts, electrostatic precipitators, tanks, boilers, process equipment, flat vertical and horizontal surfaces, furnaces, at facilities in various industries and equipment of engineering systems in residential, civil and industrial construction. The board operates in a wide temperature range of the insulated surface, depending on the board grade from -180°C to +750°C, while conventional building insulation is designed for a temperature range from -60°C to +80°C.
Application instructions:
According to the “Album of Technical Solutions for Equipment and Pipeline Thermal Insulation Systems” and installation instructions “Pipe Section Installation”.
Storage:
Store in covered warehouses, preventing exposure to precipitation. During transportation, protect from damage and moisture.
Transportation:
Transportation of boards must be carried out in accordance with the requirements of DBN G.1-4, DSTU B V.2.7-167. Products are shipped to the consumer no earlier than 24 hours after storage in the warehouse.
Packaging Information:
Polyethylene heat-shrink film is used for packaging.
Main physical and mechanical characteristics:
|
Parameter |
Unit requirement |
Technical insulation |
Test Method |
||||||
|
40 |
60 |
80 |
100 |
120 |
150 |
180 |
|||
| Density |
kg/m3 |
40 (±10) |
60 (±10) |
70-85 |
100 (±10) |
120 (±20) |
140-175 |
180 (±10) |
DSTU B V.2.7-38-95 |
| Thermal conductivity, λ25 |
W/m·K |
0,037 |
0,036 |
0,037* |
0,037 |
0,037 |
0,038 |
0,038 |
DSTU B V.2.7-105-2000 |
| Thermal conductivity, λ125 |
W/m·K |
0,056 |
0,055 |
0,045* |
0,051 |
0,050 |
0,051 |
0,051 |
DSTU B V.2.7-105-2000 |
| Thermal Conductivity, Λ300 |
W/m·K |
|
|
0,087* |
|
|
|
|
DSTU B V.2.7-105-2000 |
| Compressive strength at 10% linear deformation, not less than |
kPa |
– |
– |
– |
10 |
10 |
20 |
40 |
DSTU B V.2.7-38-95 |
| Moisture content by mass, not more than |
% |
0,5 |
DSTU B V.2.7-38-95 |
||||||
| Organic matter content, not more than |
% |
4,5 |
DSTU B V.2.7-38-95 |
||||||
| Combustibility class |
degree |
NG |
DSTU B V.2.7-70-98 |
||||||
*-according to protocol No. 61K/17.
Geometric parameters:
|
Parameter |
Unit of measurement |
Value |
| Length |
mm |
1200; 1000 (+5%; -2%) |
| Width |
mm |
500; 600 (±1.5%) |
| Thickness (depending on board density) |
mm |
40 kg/m³ – from 50-200 mm 60 kg/m³ – from 50-200 mm 80 kg/m³ – from 50-200 mm 100 kg/m³ – from 50-170 mm 120 kg/m³ – from 50-140 mm 150 kg/m³ – from 30-100 mm 180 kg/m³ – from 30-90 mm |
TU U V.2.7.-26.8-35492904-004:2010 (Amendment No. 4)
Low-combustibility thermal and sound insulation mats
Product Description:
Lamellar mats are low-combustibility thermal and sound insulation mats formed from stone wool strips (lamellas) bonded to reinforced foil. This produces a product with increased compressive strength compared to traditional mats and less deformation during installation.
In standard configuration, the mats are covered with reinforced aluminum foil. The foil covering with sealed seams serves as a vapor barrier layer, which eliminates the need for an additional vapor barrier layer on cold pipelines and air ducts.
The base of the mats consists of non-combustible stone wool lamellas.
Application:
Thermal and vapor insulation of air ducts, ventilation equipment, tanks, as well as pipelines and flat surfaces. In civil and industrial construction, for new construction and pipeline installation, and reconstruction of buildings and structures for various purposes.
Applicable at insulated surface temperatures up to +250°C on the stone wool side (on the foil side, maximum application temperature is +80°C). Provides the following functions:
thermal insulation;
vapor barrier;
finished decorative covering for indoor installations (outdoor installations require a protective covering layer).
Application instructions:
In accordance with the “Album of Technical Solutions for Thermal Insulation Systems for Equipment and Pipelines.”
Storage:
Store in covered warehouses, preventing exposure to precipitation. During transportation, protect from damage and moisture.
Transportation:
Transportation must be carried out in accordance with the requirements of DBN G.1-4, DSTU B V.2.7-167. Boards are shipped to the consumer no earlier than 24 hours after storage in the warehouse.
Packaging Information:
Polyethylene heat-shrink film is used for packaging.
Main Physical and Mechanical Characteristics
| Parameter |
Unit of measurement |
Lamellar Mat 35 |
Lamellar Mat 50 |
Test Method |
| Density |
kg/m3 |
30-45 |
40-55 |
DSTU B V.2.7-38-95 |
| Compression coefficient, Kc |
– |
1 |
1 |
SNiP 2.04.14-88 |
| Thermal conductivity, λ25 |
W/mK |
0,040* |
0,040 |
DSTU B V.2.7-105-2000 |
| Thermal conductivity, λ125 |
W/mK |
0,062* |
0,062 |
DSTU B V.2.7-105-2000 |
| Compressibility under 2 kPa load, not more than |
% |
40 |
40 |
DSTU B V.2.7-38-95 |
| Resilience, not less than |
% |
– |
65 |
DSTU B V.2.7-38-95 |
| Moisture content by mass, not more than |
% |
1 |
1 |
DSTU B V.2.7-38-95 |
| Organic matter content, not more than |
% |
4,5 |
4,5 |
DSTU B V.2.7-38-95 |
*according to protocol No. 59K/17.