TU U 22.2-32944149-012:2024
Thermal insulation boards made of extruded polystyrene foam
Product Description and Scope of Application
Extruded polystyrene foam CARBOLEX SOLID is a thermal insulation material with uniformly distributed closed cells. XPS CARBOLEX SOLID does not absorb water, does not swell, does not shrink, is chemically resistant and does not rot. High strength allows for a level and rigid base, which significantly extends the service life of the entire thermal insulation system. XPS CARBOLEX SOLID is used for thermal insulation of foundations, trafficked roofs, and floors with increased loads.
Transportation and Storage
The boards must be stored packaged and stacked on pallets separately by grades and sizes. Throughout the entire storage period, the material must be protected from atmospheric precipitation.
Packaging Information
The boards are packaged in UV-stabilized film.
Application Instructions
In accordance with SWEETONDALE Installation Instructions
|
Parameter |
Value |
Test Method |
| Compressive strength, kPa, not less than
50mm |
500 |
DSTU EN 826 |
| Tensile strength perpendicular to the board surface*, kPa |
100 |
DSTU EN 1607 |
| Declared thermal conductivity at 10°C, W/(m·K), not more than |
0,030 |
DSTU EN 12939 |
| Thermal conductivity, W/m*K λA λB |
0.034 |
DSTU B V.2.7-182 |
| Water absorption during long-term immersion, not more than, % |
0,4 |
DSTU B EN 12087 |
| Flammability |
G4 |
DBN V.1.1-7 |
| Operating temperature |
from -50 °C to +75 °C |
|
| Effective service life, years, not less than |
50 |
DSTU B V.2.7-182 |
*- tensile strength perpendicular to the face surfaces is determined for boards manufactured using the ThermoBonding method
Geometric parameters
|
Parameter |
Unit of measurement |
Value |
Test Method |
| Length |
mm |
1180 (±10) |
DSTU EN 822 |
| Width |
mm |
580 (±8) |
DSTU EN 822 |
| Thickness |
mm |
50 |
DSTU EN 822 |
| Edge type | L-edge | ||
| Thickness tolerance class | T1 | ||
TU U 22.2-32944149-012:2024
Thermal insulation boards made of extruded polystyrene foam
Product Description and Scope of Application
Extruded polystyrene foam CARBOLEX PROF features enhanced strength properties and is used for thermal insulation of foundations, floors, roofs, facades, and basements.
XPS CARBOLEX PROF contains graphite micro-particles that reflect thermal radiation and contribute to increasing the overall thermal resistance of the structure throughout the building’s service life
Transportation and Storage
The boards must be stored packaged and stacked on pallets separately by grades and sizes. Throughout the entire storage period, the material must be protected from atmospheric precipitation.
Packaging Information
The boards are packaged in UV-stabilized film.
Main physical and mechanical characteristics:
|
Parameter |
Value |
Test Method |
| Compressive strength, kPa, not less than
40mm 50mm 60mm and above |
230 250 250 |
DSTU EN 826 |
| Tensile strength perpendicular to the board surface*, kPa |
100 |
DSTU EN 1607 |
| Declared thermal conductivity at 10°C, W/(m·K), not more than |
0,032 |
DSTU EN 12939 |
| Water absorption during long-term immersion, not more than, % |
0,4 |
DSTU B EN 12087 |
| Reaction to fire |
Class F |
EN 13501-1+A1 |
| Operating temperature |
from -50 °C to +75 °C |
|
*- tensile strength perpendicular to facing surfaces is determined for boards manufactured using the ThermoBonding method
Geometric parameters:
|
Parameter |
Unit of measurement |
Value |
Test Method |
| Length |
mm |
1180 (±10) |
DSTU EN 822 |
| Width |
mm |
580 (±8) |
DSTU EN 822 |
| Thickness* |
mm |
40, 50, 60,100 |
DSTU EN 822 |
| Edge type | L-edge | ||
| Thickness tolerance class | T1 | ||
* – boards with thickness of 60 mm and above may be manufactured using the ThermoBonding method.
TU U 22.2-32944149-012:2024
Thermal insulation boards made of extruded polystyrene foam
Product Description and Scope of Application
XPS CARBOLEX ECO FAS is an insulation board made of extruded polystyrene foam with a special milled surface on both sides.
Extruded polystyrene foam CARBOLEX ECO FAS
specially designed for plastered facade structures and foundation insulation.
It can also be used for other structures where enhanced adhesion requirements are imposed on insulation boards to the substrate.
Transportation and Storage
The boards must be stored packaged and stacked on pallets separately by grades and sizes. Throughout the entire storage period, the material must be protected from atmospheric precipitation.
Packaging Information
The boards are packaged in UV-stabilized film.
Application Instructions
According to SWEETONDALE Installation Instructions https://sweetondale.cz/docs/instruktsii/
|
Parameter |
Value |
Test Method |
| Compressive strength, kPa, minimum
30 mm 40 mm 50 mm 60 mm and above |
150 150 200 200 |
DSTU EN 826 |
| Tensile strength perpendicular to the board surface*, kPa |
100 |
DSTU EN 1607 |
| Declared thermal conductivity at 10°C, W/(m·K), not more than |
0,033 |
DSTU EN 12939 |
| Thermal conductivity, W/m*K λA λB |
0.035 |
DSTU B V.2.7-182 |
| Water absorption during long-term immersion, not more than, % |
0,4 |
DSTU B EN 12087 |
| Flammability |
G4 |
DBN V.1.1-7 |
| Operating temperature |
from -50 °C to +75 °C |
|
| Effective service life, years, not less than |
50 |
DSTU B V.2.7-182 |
*- tensile strength perpendicular to the face surfaces is determined for boards manufactured using the ThermoBonding method
Geometric parameters:
|
Parameter |
Unit of measurement |
Value |
Test Method |
| Length |
mm |
1180 (±10) |
DSTU EN 822 |
| Width |
mm |
580 (±8) |
DSTU EN 822 |
| Thickness*, boards with L-edge |
mm |
30, 40, 50, 100 |
DSTU EN 822 |
| Thickness tolerance class | T1 | ||
* – boards with a thickness of 60 mm and above may be manufactured using the ThermoBonding method
TU U 22.2-32944149-012:2024
Thermal insulation boards made of extruded polystyrene foam
Product Description and Scope of Application
Extruded polystyrene foam CARBOLEX ECO is a thermal insulation material with uniformly distributed closed cells.
XPS CARBOLEX ECO does not absorb water, does not swell or shrink, is chemically resistant and not susceptible to rot.
High strength allows for a level and rigid base, which significantly extends the service life of the entire thermal insulation system.
XPS CARBOLEX ECO is used in cottage and low-rise construction for thermal insulation of foundations, roofs, floors, and facade insulation.
Transportation and Storage
The boards must be stored packaged and stacked on pallets separately by grades and sizes. Throughout the entire storage period, the material must be protected from atmospheric precipitation.
Packaging Information
The boards are packaged in UV-stabilized film.
Application Instructions
In accordance with SWEETONDALE Installation Instructions
| Parameter |
Value |
Test Method |
| Compressive strength, kPa, not less than
20 mm 30 mm 40 mm 50 mm 60 mm and above |
150 150 150 200 200 |
DSTU EN 826 |
| Tensile strength perpendicular to the board surface*, kPa |
100 |
DSTU EN 1607 |
| Declared thermal conductivity at 10°C, W/(m·K), not more than |
0,033 |
DSTU EN 12939 |
| Thermal conductivity, W/m*K λA λB |
0.035 |
DSTU B V.2.7-182 |
| Water absorption during long-term immersion, not more than, % |
0,4 |
DSTU B EN 12087 |
| Flammability |
G4 |
DBN V.1.1-7 |
| Operating temperature |
from -50 °C to +75 °C |
|
| Effective service life, years, not less than |
50 |
DSTU B V.2.7-182 |
*- tensile strength perpendicular to the facing surfaces is determined for boards manufactured using the ThermoBonding method
|
Parameter |
Unit of measurement |
Value, L-edge |
Value, straight edge |
Test Method |
| Length |
mm |
1180 (±10) |
1180 (±10) |
DSTU EN 822 |
| Width |
mm |
580 (±8) |
580 (±8) |
DSTU EN 822 |
| Thickness* |
mm |
30,40,50,100 |
20 |
DSTU EN 822 |
| Thickness tolerance class |
T1 |
|||
* – boards with a thickness of 60 mm and above may be manufactured using the ThermoBonding method