TU U 23.9-32944149-013:2024
Roll roofing and waterproofing material
Product Description and Scope of Application
HYDROBASE ELAST is a torch-applied bitumen-polymer roofing and waterproofing roll material.
HYDROBASE ELAST is produced by applying a bitumen-polymer binder on both sides of a polyester base. The binder consists of bitumen, SBS polymer modifier (styrene-butadiene-styrene), and mineral filler (talc, dolomite, etc.). Coarse-grained granules and polymer films are used as protective layers.
Depending on the type of surfacing and application area, HYDROBASE ELAST is available in two grades:
HYDROBASE ELAST EKP – with coarse-grained surfacing on the top side and polymer film on the torch-applied side; used for installing the top layer of the roofing membrane;
HYDROBASE ELAST EPP – with polymer film on both sides of the sheet; used for installing the bottom layer of the roofing membrane and waterproofing building structures (foundations, tunnels, etc.)
Transportation and Storage
Transportation is carried out by all types of transport in covered vehicles in accordance with the Cargo Transportation Rules applicable to the given type of transport. Throughout the entire storage period, the material must be protected from atmospheric precipitation. Rolls are stored vertically on pallets in a single row by height.
The guaranteed shelf life of the product in rolls is 12 months from the date of manufacture in factory packaging, provided storage and transportation conditions are observed.
Packaging Information
The material is packaged in UV-stabilized film and supplied on pallets
Application Instructions
In accordance with SWEETONDALE Installation Instructions
Main characteristics
| Parameter name | HYDROBASE ELAST EPP | HYDROBASE ELAST EKP |
Test Method |
||
| Thickness, mm |
4.0 ± 0.2 |
4.2 ± 0.2 |
EN 1849-1 |
||
| Mass per unit area, kg/m²* (+0.25 kg) |
5,2 |
5,5 |
EN 1849-1 |
||
| Watertightness at 2 kPa pressure for 24 hours |
– |
No water penetration |
EN 1928 |
||
| Watertightness at 60 kPa pressure for 24 hours |
No water penetration |
– |
EN 1928 |
||
| Tensile strength, N, minimum
– longitudinal/transverse |
588/392 |
588/392 |
DSTU B V.2.7-83 |
||
| Flexibility on a bar with a radius of (25.0±0.2) mm at temperature, °C, maximum |
-25 |
-25 |
DSTU B V.2.7-83 |
||
| Flow resistance at elevated temperature, °C |
≥100 |
≥100 |
EN 1110 |
||
| Loss of coarse-grained surfacing, g/sample, maximum |
– |
1 |
DSTU B V.2.7-83 |
||
| Type of protective coating: |
|
|
|||
| top side
torch-on side |
film without logo film with logo |
slate film with logo |
|
||
| Length/width, m |
10×1 |
10×1 |
|||
| Pallet packaging |
white heat-shrink bag with logo |
||||
*- the mass per 1 m² is provided for reference; the material is standardized by thickness. The manufacturer reserves the right to change this parameter;
TU U 23.9-32944149-013:2024
Roll roofing and waterproofing material
Product Description and Scope of Application
HYDROBASE VENT is a torch-applied bitumen-polymer roofing and waterproofing roll material.
HYDROBASE VENT EKV consists of a polyester fabric base coated on both sides with bitumen-polymer binder, with protective layers on top in the form of coarse-grained granules and on the bottom in the form of fine-grained granules. An additional layer of bitumen-polymer binder is applied in strips to the lower protective layer. To prevent the material from sticking, the strips are covered with a polymer film. The material is used for installing a single-layer ventilated (“breathable”) roofing membrane.
HYDROBASE VENT EPV consists of a polyester fabric base coated on both sides with bitumen-polymer binder, with protective layers on top in the form of polyethylene film and on the bottom in the form of fine-grained granules. An additional layer of bitumen-polymer binder is applied in strips to the lower protective layer. To prevent the material from sticking, the strips are covered with a polymer film. The material is used for installing the bottom layer of a two-layer ventilated (“breathable”) roofing membrane.
Transportation and Storage
Transportation is carried out by all types of transport in covered vehicles in accordance with the Cargo Transportation Rules applicable to the given type of transport. Throughout the entire storage period, the material must be protected from atmospheric precipitation. Rolls are stored vertically on pallets in a single row by height.
Packaging Information
The material is packaged in UV-stabilized film and supplied on pallets.
Application Instructions
In accordance with SWEETONDALE Installation Instructions
Main characteristics
| Parameter name | HYDROBASE VENT EPV | HYDROBASE VENT EKV |
Test Method |
||
| Thickness, mm |
3.8 ± 0.2 |
4.2 ± 0.2 |
EN 1849-1 |
||
| Mass per unit area, kg/m²* (+0.25 kg) |
4,8 |
5,0 |
EN 1849-1 |
||
| Watertightness at 2 kPa pressure for 24 hours |
No water penetration |
EN 1928 |
|||
| Watertightness at 60 kPa pressure for 24 hours |
– |
EN 1928 |
|||
| Tensile strength, N, minimum
– longitudinal/transverse |
489/343 |
588/392 |
DSTU B V.2.7-83 |
||
| Flexibility on a bar with a radius of (25.0±0.2) mm at temperature, °C, maximum |
-20 |
-20 |
DSTU B V.2.7-83 |
||
| Flow resistance at elevated temperature, °C |
≥95 |
≥95 |
EN 1110 |
||
| Loss of coarse-grained surfacing, g/sample, maximum |
– |
1 |
DSTU B V.2.7-83 |
||
| Reaction to fire | Class E | DSTU EN 13501-1 | |||
| Type of protective coating: |
|
|
|||
| top side
torch-on side |
film ventilated covering |
slate ventilated covering |
|
||
| Length/width, m |
10×1 |
10×1 | |||
| Pallet packaging |
white heat-shrink bag with logo |
||||
*- the mass per 1 m² is provided for reference; the material is standardized by thickness. The manufacturer reserves the right to change this parameter;
TU U 22.2-32944149-012:2024
Thermal insulation boards made of extruded polystyrene foam
Product Description and Scope of Application
Extruded polystyrene foam CARBOLEX PROF features enhanced strength properties and is used for thermal insulation of foundations, floors, roofs, facades, and basements.
XPS CARBOLEX PROF contains graphite micro-particles that reflect thermal radiation and contribute to increasing the overall thermal resistance of the structure throughout the building’s service life
Transportation and Storage
The boards must be stored packaged and stacked on pallets separately by grades and sizes. Throughout the entire storage period, the material must be protected from atmospheric precipitation.
Packaging Information
The boards are packaged in UV-stabilized film.
Main physical and mechanical characteristics:
|
Parameter |
Value |
Test Method |
| Compressive strength, kPa, not less than
40mm 50mm 60mm and above |
230 250 250 |
DSTU EN 826 |
| Tensile strength perpendicular to the board surface*, kPa |
100 |
DSTU EN 1607 |
| Declared thermal conductivity at 10°C, W/(m·K), not more than |
0,032 |
DSTU EN 12939 |
| Water absorption during long-term immersion, not more than, % |
0,4 |
DSTU B EN 12087 |
| Reaction to fire |
Class F |
EN 13501-1+A1 |
| Operating temperature |
from -50 °C to +75 °C |
|
*- tensile strength perpendicular to facing surfaces is determined for boards manufactured using the ThermoBonding method
Geometric parameters:
|
Parameter |
Unit of measurement |
Value |
Test Method |
| Length |
mm |
1180 (±10) |
DSTU EN 822 |
| Width |
mm |
580 (±8) |
DSTU EN 822 |
| Thickness* |
mm |
40, 50, 60,100 |
DSTU EN 822 |
| Edge type | L-edge | ||
| Thickness tolerance class | T1 | ||
* – boards with thickness of 60 mm and above may be manufactured using the ThermoBonding method.
TU U V.2.7-23.9-35492904-006:2024
Thermal and acoustic insulation boards made of mineral wool
Product Description and Scope of Application
ULTRAWOOL VIBRO is a non-combustible, hydrophobized thermal and sound insulation board made of mineral wool based on basalt group rocks. ULTRAWOOL VIBRO boards are designed for thermal and sound insulation of floating floors when laying concrete or cement screed directly on the thermal insulation.
Transportation and Storage
Transportation of boards is carried out in accordance with the requirements of DSTU B V.2.7-167. Boards are shipped to the consumer no earlier than 24 hours after storage at the warehouse. Boards must be stored packaged and stacked on pallets separately by grades and sizes. Throughout the entire storage period, the material must be protected from precipitation. The height of the board stack during storage must not exceed 3 m. Guaranteed storage period is 6 months from the date of manufacture.
Packaging Information
Polyethylene heat-shrink film is used for packaging. The method of wrapping and fixing the packaging material ensures reliable and durable packaging of the boards, their protection during loading and unloading operations, transportation and storage.
Main physical and mechanical characteristics:
|
Parameter |
Value |
Test Method |
| Density, kg/m3 |
110±11 |
DSTU B V.2.7-38 |
| Declared thermal conductivity at 10°C, W/(m·K), not more than |
0,036 |
DSTU B EN 12667 |
| Thermal conductivity, W/m*K λA λB |
0.040 |
DSTU B V.2.7-182 |
| Compressive stress at 10% linear deformation, kPa, not less than |
25 |
DSTU EN 826 |
| Tensile strength in the direction perpendicular to the board plane, kPa, not less than |
– |
DSTU EN 1607 |
| Point load, N, minimum |
50 |
EN 12430 |
| Long-term water absorption, kg/m2, not more than |
3 |
EN 12087 |
| Short-term water absorption, kg/m2, not more than |
1 |
EN 1609 |
| Reaction to fire |
A1 |
DSTU EN 13501-1 |
| Combustibility class |
NG |
DBN V.1.1-7 |
Geometric parameters:
|
Parameter |
Unit of measurement |
Value |
Test Method |
| Length |
mm |
1200 |
DSTU EN 822 |
| Width |
mm |
600 |
DSTU EN 822 |
| Thickness (in 10 mm increments) |
mm |
50-200 |
DSTU EN 823 |
| Tolerance limits length / width |
mm |
±2 / ±1.5% |
DSTU EN 13162 |
| Thickness tolerance class | T4 | ||
| Logistics Parameters: | ||
| Length, mm | 1200 | 1200 |
| Width, mm | 600 | 600 |
| Thickness, mm | 50 | 100 |
| Boards per pack, pcs | 6 | 3 |
| Coverage per pack, m2 | 4.32 | 2.160 |
| Volume per pack, m3 | 0.216 | 0.216 |
| Packs per pallet, pcs | 32 | 32 |
| Volume per pallet, m3 | 6.912 | 7.912 |
| Truck loading capacity (92 m3), m3 | 76.032 | 76.032 |
TU U V.2.7-23.9-35492904-006:2024
Thermal and acoustic insulation boards made of mineral wool
Product Description and Scope of Application
THERMOWOOL FLOOR is a non-combustible, hydrophobized thermal and sound insulation board made from mineral wool based on basalt group rock. THERMOWOOL FLOOR boards are designed for thermal and sound insulation of floating floors when laying concrete or cement screed directly on the thermal insulation.
Transportation and Storage
Transportation of the boards is carried out in accordance with the requirements of DSTU B V.2.7-167. The boards must be stored packaged and stacked on pallets separately by grade and size. Throughout the entire storage period, the material must be protected from atmospheric precipitation. The height of the board stack during storage must not exceed 3 m. The guaranteed storage period is 6 months from the date of manufacture.
Packaging Information
Polyethylene heat-shrink film is used for packaging. The wrapping method and fixation of the packaging material ensure reliable and durable packaging of the boards, protecting them during loading and unloading operations, transportation, and storage.
Application Instructions
In accordance with SWEETONDALE Installation Instructions
Main physical and mechanical characteristics:
|
Parameter |
THERMOWOOL FLOOR STANDARD 110 |
THERMOWOOL FLOOR PROF 170 |
Test Method |
| Density, kg/m3 |
110±11 |
170±15 |
DSTU B V.2.7-38 |
| Declared thermal conductivity at 10°C, W/(m·K), not more than |
0,036 |
0,039 |
DSTU B EN 12667 |
| Thermal conductivity, W/m*K λA λB |
0.040 |
0.043 |
DSTU B V.2.7-182 |
| Compressive stress at 10% linear deformation, kPa, not less than |
25 |
50 |
DSTU EN 826 |
| Point load, N, minimum |
50 |
600 |
EN 12430 |
| Impact sound insulation improvement index of the floor, dB
30mm 40mm 50mm |
36 38 40 |
|
DSTU B V.2.6-86 ISO 140-6 |
| Reaction to fire |
A1 |
A1 |
DSTU EN 13501-1 |
| Combustibility class |
NG |
NG |
DBN V.1.1-7 |
| Effective service life, years, not less than |
50 |
50 |
DSTU B V.2.7-182 |
Geometric parameters:
|
Parameter |
Unit of measurement |
THERMOWOOL FLOOR STANDARD 110 |
THERMOWOOL FLOOR PROF 170 |
Test Method |
||
| Length |
mm |
1200 |
1200 |
DSTU EN 822 |
||
| Width |
mm |
600 |
600 |
DSTU EN 822 |
||
| Thickness (in 10 mm increments) |
mm |
50-200 |
30-100 |
DSTU EN 823 |
||
| Tolerance limits length / width |
mm |
±2 / ±1.5% |
±2 / ±1.5% |
DSTU EN 13162 |
||
| Thickness tolerance class | T4 T5 | |||||
Logistics parameters:
| Length, mm | 1200 | 1200 |
| Width, mm | 600 | 600 |
| Thickness, mm | 50 | 30 |
| Quantity per package, boards, pcs | 6 | 7 |
| Quantity per package, m2 | 4.32 | 5.04 |
| Quantity per package, m3 | 0.216 | 0.151 |
| Quantity per pallet, packages, pcs | 32 | 48 |
| Quantity per pallet, m3 | 6.912 | 7.258 |
| Loading capacity in vehicle, volume 92, m3 | 76.032 | 79.834 |