TU U 23.9-32944149-013:2024
Roll roofing and waterproofing material
Product Description and Scope of Application
HYDROBASE STANDARD consists of a base made of fiberglass or polyester fabric or a combined base, coated on both sides with bituminous binder, with protective layers on top in the form of coarse-grained granules or polymer film and on the bottom in the form of polymer film. The materials are manufactured for torch-on application.
Depending on the type of protective layers and area of application, the following grades are available:
HYDROBASE STANDARD K – with coarse-grained granules on the face side and polymer film on the torch-on application side of the sheet; used for installation of the top layer of the roofing membrane;
HYDROBASE STANDARD P – with polymer film on the face and bottom sides of the sheet; used for installation of the bottom layers of the roofing membrane and waterproofing of building structures
Transportation and Storage
Transportation is carried out by all types of transport in covered vehicles in accordance with the Cargo Transportation Rules applicable to the given type of transport. Throughout the entire storage period, the material must be protected from atmospheric precipitation. Rolls are stored vertically on pallets in a single row by height.
Packaging Information
The material is packaged in UV-stabilized film and supplied on pallets
Application Instructions
In accordance with SWEETONDALE Installation Instructions
Main characteristics
| Parameter name |
HYDROBASE STANDARD P |
HYDROBASE STANDARD K |
Test Method |
||
| Mass per unit area, kg/m²* |
2,5 |
4,0 |
EN 1849-1 |
||
| Watertightness at 2 kPa pressure for 24 hours |
– |
– |
EN 1928 |
||
| Watertightness at 60 kPa pressure for 24 hours |
No water penetration |
No water penetration |
EN 1928 |
||
| Tensile strength along / across the sheet, N, not less than for material:
on fiberglass fabric on polyester fabric |
294/- 343/- |
294/- 343/- |
DSTU B V.2.7-83 |
||
| Flexibility on a bar with a radius of (25.0±0.2) mm at temperature, °C, maximum |
-10 |
-10 |
DSTU B V.2.7-83 |
||
| Flow resistance at elevated temperature, °C |
≥90 |
≥90 |
EN 1110 |
||
| Loss of coarse-grained surfacing, g/sample, maximum |
– |
2 |
DSTU B V.2.7-83 |
||
| Reaction to fire | Class E | DSTU EN 13501-1 | |||
| Type of protective coating: |
|
|
|||
| top side
torch-on side |
film without logo film without logo |
slate film without logo |
|
||
| Length/width, m |
15×1 |
10×1 |
|||
| Pallet packaging |
white heat-shrink bag with logo |
||||
* – deviation from the nominal value of 1 m² mass shall not exceed ±0.25 kg
TU U 23.9-32944149-013:2024
Roll roofing and waterproofing material
Product Description and Scope of Application
HYDROBASE FLEX is a torch-applied bitumen-polymer roll roofing and waterproofing material.
HYDROBASE FLEX is produced by applying a bitumen-polymer binder on both sides of a polyester base. The binder consists of bitumen, SBS polymer modifier (styrene-butadiene-styrene), and mineral filler (talc, dolomite, etc.). Coarse-grained surfacing and polymer films are used as protective layers.
Depending on the type of surfacing and application area, HYDROBASE FLEX is available in two grades:
HYDROBASE FLEX K – with coarse-grained surfacing on the top side and polymer film on the torch-applied side; used for installation of the upper layer of the roofing membrane;
HYDROBASE FLEX P – with polymer film on both sides of the sheet; used for installation of the lower layer of the roofing membrane and waterproofing of building structures (foundations, tunnels, etc.)
Transportation and Storage
Transportation is carried out by all types of transport in covered vehicles in accordance with the Cargo Transportation Rules applicable to the given type of transport. Throughout the entire storage period, the material must be protected from atmospheric precipitation. Rolls are stored vertically on pallets in a single row by height.
Packaging Information
The material is packaged in UV-stabilized film and supplied on pallets
Application Instructions
In accordance with SWEETONDALE Installation Instructions
Main characteristics
| Parameter name | HYDROBASE FLEX EPP | HYDROBASE FLEX EKP |
Test Method |
|||||
| Thickness, mm |
2.8 ± 0.2 |
3.8 ± 0.2 |
EN 1849-1 |
|||||
| Mass per unit area, kg/m²* (+0.25 kg) |
4,1 |
5,3 |
EN 1849-1 |
|||||
| Watertightness at 2 kPa pressure for 24 hours |
– |
No water penetration |
EN 1928 |
|||||
| Watertightness at 60 kPa pressure for 24 hours |
No water penetration |
– |
EN 1928 |
|||||
| Tensile strength, N, minimum
– longitudinal/transverse |
489/343 |
489/343 |
DSTU B V.2.7-83 |
|||||
| Flexibility on a bar with a radius of (25.0±0.2) mm at temperature, °C, maximum |
-20 |
-20 |
DSTU B V.2.7-83 |
|||||
| Flow resistance at elevated temperature, °C |
≥95 |
≥95 |
EN 1110 |
|||||
| Loss of coarse-grained surfacing, g/sample, maximum |
– |
1 |
DSTU B V.2.7-83 |
|||||
| Reaction to fire | Class E | DSTU EN 13501-1 | ||||||
| Type of protective coating:
upper side |
film without logo |
slate |
|
|||||
| torch-applied side |
film with logo |
film with logo |
|
|||||
| Length/width, m |
10×1 |
10×1 |
||||||
| Pallet packaging |
white heat-shrink bag with logo |
|||||||
*- the mass per 1 m² is provided for reference; the material is standardized by thickness. The manufacturer reserves the right to change this parameter;
TU U 22.2-32944149-012:2024
Thermal insulation boards made of extruded polystyrene foam
Product Description and Scope of Application
Extruded polystyrene foam CARBOLEX SOLID is a thermal insulation material with uniformly distributed closed cells. XPS CARBOLEX SOLID does not absorb water, does not swell, does not shrink, is chemically resistant and does not rot. High strength allows for a level and rigid base, which significantly extends the service life of the entire thermal insulation system. XPS CARBOLEX SOLID is used for thermal insulation of foundations, trafficked roofs, and floors with increased loads.
Transportation and Storage
The boards must be stored packaged and stacked on pallets separately by grades and sizes. Throughout the entire storage period, the material must be protected from atmospheric precipitation.
Packaging Information
The boards are packaged in UV-stabilized film.
Application Instructions
In accordance with SWEETONDALE Installation Instructions
|
Parameter |
Value |
Test Method |
| Compressive strength, kPa, not less than
50mm |
500 |
DSTU EN 826 |
| Tensile strength perpendicular to the board surface*, kPa |
100 |
DSTU EN 1607 |
| Declared thermal conductivity at 10°C, W/(m·K), not more than |
0,030 |
DSTU EN 12939 |
| Thermal conductivity, W/m*K λA λB |
0.034 |
DSTU B V.2.7-182 |
| Water absorption during long-term immersion, not more than, % |
0,4 |
DSTU B EN 12087 |
| Flammability |
G4 |
DBN V.1.1-7 |
| Operating temperature |
from -50 °C to +75 °C |
|
| Effective service life, years, not less than |
50 |
DSTU B V.2.7-182 |
*- tensile strength perpendicular to the face surfaces is determined for boards manufactured using the ThermoBonding method
Geometric parameters
|
Parameter |
Unit of measurement |
Value |
Test Method |
| Length |
mm |
1180 (±10) |
DSTU EN 822 |
| Width |
mm |
580 (±8) |
DSTU EN 822 |
| Thickness |
mm |
50 |
DSTU EN 822 |
| Edge type | L-edge | ||
| Thickness tolerance class | T1 | ||
TU U 22.2-32944149-012:2024
Thermal insulation boards made of extruded polystyrene foam
Product Description and Scope of Application
Extruded polystyrene foam CARBOLEX ECO is a thermal insulation material with uniformly distributed closed cells.
XPS CARBOLEX ECO does not absorb water, does not swell or shrink, is chemically resistant and not susceptible to rot.
High strength allows for a level and rigid base, which significantly extends the service life of the entire thermal insulation system.
XPS CARBOLEX ECO is used in cottage and low-rise construction for thermal insulation of foundations, roofs, floors, and facade insulation.
Transportation and Storage
The boards must be stored packaged and stacked on pallets separately by grades and sizes. Throughout the entire storage period, the material must be protected from atmospheric precipitation.
Packaging Information
The boards are packaged in UV-stabilized film.
Application Instructions
In accordance with SWEETONDALE Installation Instructions
| Parameter |
Value |
Test Method |
| Compressive strength, kPa, not less than
20 mm 30 mm 40 mm 50 mm 60 mm and above |
150 150 150 200 200 |
DSTU EN 826 |
| Tensile strength perpendicular to the board surface*, kPa |
100 |
DSTU EN 1607 |
| Declared thermal conductivity at 10°C, W/(m·K), not more than |
0,033 |
DSTU EN 12939 |
| Thermal conductivity, W/m*K λA λB |
0.035 |
DSTU B V.2.7-182 |
| Water absorption during long-term immersion, not more than, % |
0,4 |
DSTU B EN 12087 |
| Flammability |
G4 |
DBN V.1.1-7 |
| Operating temperature |
from -50 °C to +75 °C |
|
| Effective service life, years, not less than |
50 |
DSTU B V.2.7-182 |
*- tensile strength perpendicular to the facing surfaces is determined for boards manufactured using the ThermoBonding method
|
Parameter |
Unit of measurement |
Value, L-edge |
Value, straight edge |
Test Method |
| Length |
mm |
1180 (±10) |
1180 (±10) |
DSTU EN 822 |
| Width |
mm |
580 (±8) |
580 (±8) |
DSTU EN 822 |
| Thickness* |
mm |
30,40,50,100 |
20 |
DSTU EN 822 |
| Thickness tolerance class |
T1 |
|||
* – boards with a thickness of 60 mm and above may be manufactured using the ThermoBonding method