TU U 23.9-32944149-013:2024
Roll roofing and waterproofing material
Product Description and Scope of Application
HYDROBASE ELAST is a torch-applied bitumen-polymer roofing and waterproofing roll material.
HYDROBASE ELAST is produced by applying a bitumen-polymer binder on both sides of a polyester base. The binder consists of bitumen, SBS polymer modifier (styrene-butadiene-styrene), and mineral filler (talc, dolomite, etc.). Coarse-grained granules and polymer films are used as protective layers.
Depending on the type of surfacing and application area, HYDROBASE ELAST is available in two grades:
HYDROBASE ELAST EKP – with coarse-grained surfacing on the top side and polymer film on the torch-applied side; used for installing the top layer of the roofing membrane;
HYDROBASE ELAST EPP – with polymer film on both sides of the sheet; used for installing the bottom layer of the roofing membrane and waterproofing building structures (foundations, tunnels, etc.)
Transportation and Storage
Transportation is carried out by all types of transport in covered vehicles in accordance with the Cargo Transportation Rules applicable to the given type of transport. Throughout the entire storage period, the material must be protected from atmospheric precipitation. Rolls are stored vertically on pallets in a single row by height.
The guaranteed shelf life of the product in rolls is 12 months from the date of manufacture in factory packaging, provided storage and transportation conditions are observed.
Packaging Information
The material is packaged in UV-stabilized film and supplied on pallets
Application Instructions
In accordance with SWEETONDALE Installation Instructions
Main characteristics
| Parameter name | HYDROBASE ELAST EPP | HYDROBASE ELAST EKP |
Test Method |
||
| Thickness, mm |
4.0 ± 0.2 |
4.2 ± 0.2 |
EN 1849-1 |
||
| Mass per unit area, kg/m²* (+0.25 kg) |
5,2 |
5,5 |
EN 1849-1 |
||
| Watertightness at 2 kPa pressure for 24 hours |
– |
No water penetration |
EN 1928 |
||
| Watertightness at 60 kPa pressure for 24 hours |
No water penetration |
– |
EN 1928 |
||
| Tensile strength, N, minimum
– longitudinal/transverse |
588/392 |
588/392 |
DSTU B V.2.7-83 |
||
| Flexibility on a bar with a radius of (25.0±0.2) mm at temperature, °C, maximum |
-25 |
-25 |
DSTU B V.2.7-83 |
||
| Flow resistance at elevated temperature, °C |
≥100 |
≥100 |
EN 1110 |
||
| Loss of coarse-grained surfacing, g/sample, maximum |
– |
1 |
DSTU B V.2.7-83 |
||
| Type of protective coating: |
|
|
|||
| top side
torch-on side |
film without logo film with logo |
slate film with logo |
|
||
| Length/width, m |
10×1 |
10×1 |
|||
| Pallet packaging |
white heat-shrink bag with logo |
||||
*- the mass per 1 m² is provided for reference; the material is standardized by thickness. The manufacturer reserves the right to change this parameter;
TU U V.2.7-23.9-35492904-006:2024
Thermal and acoustic insulation boards made of mineral wool
Product Description and Scope of Application
THERMOWOOL FAS STANDARD 100 boards are designed for use as a thermal insulation layer in facade systems with an external plaster layer on low-rise buildings and structures (up to 10 m high), as well as on wall sections located inside glazed loggias and balconies, staircases and landings of multi-story buildings regardless of their height
Transportation and Storage
Transportation of boards is carried out in accordance with the requirements of DSTU B V.2.7-167. Boards are shipped to the consumer no earlier than 24 hours after storage at the warehouse. Boards must be stored packaged and stacked on pallets separately by grades and sizes. Throughout the entire storage period, the material must be protected from precipitation. The height of the board stack during storage must not exceed 3 m. Guaranteed storage period is 6 months from the date of manufacture.
Packaging Information
Polyethylene heat-shrink film is used for packaging. The wrapping method and fixation of the packaging material ensure reliable and durable packaging of the boards, protecting them during loading and unloading operations, transportation, and storage.
Application Instructions
In accordance with SWEETONDALE Installation Instructions
Main physical and mechanical characteristics:
|
Parameter |
Value |
Test Method |
| Density, kg/m3 |
100±10 |
DSTU B V.2.7-38 |
| Declared thermal conductivity at 10°C, W/(m·K), not more than |
0,036 |
DSTU B EN 12667 |
| Compressive stress at 10% linear deformation, kPa, not less than |
20 |
DSTU EN 826 |
| Tensile strength in the direction perpendicular to the board plane, kPa, not less than |
10 |
DSTU EN 1607 |
| Long-term water absorption, kg/m2, not more than |
3 |
EN 12087 |
| Short-term water absorption, kg/m2, not more than |
1 |
EN 1609 |
| Reaction to fire |
A1 |
DSTU EN 13501-1 |
| Combustibility class |
NG |
DBN V.1.1-7 |
Geometric parameters:
|
Parameter |
Unit of measurement |
Value |
Test Method |
| Length |
mm |
1200 |
DSTU EN 822 |
| Width |
mm |
600 |
DSTU EN 822 |
| Thickness (in 10 mm increments) |
mm |
50 – 200 |
DSTU EN 823 |
| Tolerance limits length / width |
mm |
±2 / ±1.5% |
DSTU EN 13162 |
| Thickness tolerance class | T5 | ||
Logistics parameters:
| Length, mm | 1200 | 1200 | 1200 |
| Width, mm | 600 | 600 | 600 |
| Thickness, mm | 50 | 100 | 150 |
| Quantity per package, boards, pcs | 6 | 3 | |
| Quantity per package, m2 | 4.320 | 2.160 | |
| Quantity per package, m3 | 0.216 | 0.216 | |
| Quantity per pallet, packages, pcs | 32 | 32 | |
| Quantity per pallet, m3 | 6.912 | 6.912 | |
| Loading capacity in truck, volume 92 m3 | 76.032 | 76.032 |
TU U V.2.7-23.9-35492904-006:2024
Thermal and acoustic insulation boards made of mineral wool
Product Description and Scope of Application
THERMOWOOL slabs FAS EXTRA 90 are designed for use as a thermal insulation layer in facade systems with an external plaster layer for application indoors on glazed loggias and balconies (height limitation up to 3 m) in multi-story buildings
Transportation and Storage
Transportation of boards is carried out in accordance with the requirements of DSTU B V.2.7-167. Boards are shipped to the consumer no earlier than 24 hours after storage at the warehouse. Boards must be stored packaged and stacked on pallets separately by grades and sizes. Throughout the entire storage period, the material must be protected from precipitation. The height of the board stack during storage must not exceed 3 m. Guaranteed storage period is 6 months from the date of manufacture.
Packaging Information
Polyethylene heat-shrink film is used for packaging. The wrapping method and fixation of the packaging material ensure reliable and durable packaging of the boards, protecting them during loading and unloading operations, transportation, and storage.
Application Instructions
In accordance with SWEETONDALE Installation Instructions
Main physical and mechanical characteristics:
|
Parameter |
Value |
Test Method |
| Density, kg/m3 |
90±10 |
DSTU B V.2.7-38 |
| Declared thermal conductivity at 10°C, W/(m·K), not more than |
0,036 |
DSTU B EN 12667 |
| Compressive stress at 10% linear deformation, kPa, not less than |
15 |
DSTU EN 826 |
| Tensile strength in the direction perpendicular to the board plane, kPa, not less than |
5 |
DSTU EN 1607 |
| Long-term water absorption, kg/m2, not more than |
3 |
EN 12087 |
| Short-term water absorption, kg/m2, not more than |
1 |
EN 1609 |
| Reaction to fire |
A1 |
DSTU EN 13501-1 |
| Combustibility class |
NG |
DBN V.1.1-7 |
Geometric parameters:
|
Parameter |
Unit of measurement |
Value |
Test Method |
| Length |
mm |
1200 |
DSTU EN 822 |
| Width |
mm |
600 |
DSTU EN 822 |
| Thickness (in 10 mm increments) |
mm |
50 – 200 |
DSTU EN 823 |
| Tolerance limits length / width |
mm |
±2 / ±1.5% |
DSTU EN 13162 |
| Thickness tolerance class | T5 | ||
Logistics parameters:
| Length, mm | 1200 | 1200 | 1200 |
| Width, mm | 600 | 600 | 600 |
| Thickness, mm | 50 | 100 | 150 |
| Quantity per package, boards, pcs | 6 | 3 | |
| Quantity per package, m2 | 4.320 | 2.160 | |
| Quantity per package, m3 | 0.216 | 0.216 | |
| Quantity per pallet, packages, pcs | 32 | 32 | |
| Quantity per pallet, m3 | 6.912 | 6.912 | |
| Loading capacity in truck, volume 92 m3 | 76.032 | 76.032 |
TU U 23.9-32944149-013:2024
Roll roofing and waterproofing material
Product Description and Scope of Application
HYDROBASE ULTRA consists of a base made of fiberglass or polyester fabric or a combined base, coated on both sides with bitumen-polymer binder, with protective layers on top in the form of coarse-grained granules or polymer film and on the bottom in the form of polymer film. The materials are manufactured for torch-on application.
Depending on the type of protective layers and area of application, the following grades are available:
HYDROBASE ULTRA K – with coarse-grained granules on the face side and polymer film on the torch-on side of the sheet; used for installation of the top layer of the roofing membrane;
HYDROBASE ULTRA P – with polymer film on the face and bottom sides of the sheet; used for installation of lower layers of the roofing membrane and waterproofing of building structures, as well as for vapor barrier.
Transportation and Storage
Transportation is carried out by all types of transport in covered vehicles in accordance with the Cargo Transportation Rules applicable to the given type of transport. Throughout the entire storage period, the material must be protected from atmospheric precipitation. Rolls are stored vertically on pallets in a single row by height.
Packaging Information
The material is packaged in UV-stabilized film and supplied on pallets
Application Instructions
In accordance with SWEETONDALE Installation Instructions
Main characteristics
| Parameter name | HYDROBASE ULTRA P | HYDROBASE ULTRA K |
Test Method |
||
| Mass per unit area, kg/m²* |
3,0 |
4,0 |
EN 1849-1 |
||
|
3,5 ** |
4,5 ** |
||||
| Watertightness at 2 kPa pressure for 24 hours |
– |
No water penetration |
EN 1928 |
||
| Watertightness at 60 kPa pressure for 24 hours |
No water penetration |
– |
EN 1928 |
||
| Tensile strength along / across the sheet, N, not less than for material:
on fiberglass fabric on polyester fabric |
343/- 400/- |
343/- 400/- |
DSTU B V.2.7-83 |
||
| Flexibility on a bar with a radius of (25.0±0.2) mm at temperature, °C, maximum |
-15 |
-15 |
DSTU B V.2.7-83 |
||
| Flow resistance at elevated temperature, °C |
≥105 |
≥105 |
EN 1110 |
||
| Loss of coarse-grained surfacing, g/sample, maximum |
– |
1 |
DSTU B V.2.7-83 |
||
| Reaction to fire | Class E | DSTU EN13501-1 | |||
| Type of protective coating: |
|
|
|||
| top side
torch-on side |
film without logo film with logo |
slate film with logo |
|
||
| Length/width, m |
15×1 |
10×1 |
|||
| Pallet packaging |
white heat-shrink bag with logo |
||||
* – deviation from the nominal value of 1 m² mass shall not exceed ±0.25 kg
** – custom manufacturing is available upon request.
TU U 23.9-32944149-013:2024
Roll roofing and waterproofing material
Product Description and Scope of Application
HYDROBASE FLEX is a torch-applied bitumen-polymer roll roofing and waterproofing material.
HYDROBASE FLEX is produced by applying a bitumen-polymer binder on both sides of a polyester base. The binder consists of bitumen, SBS polymer modifier (styrene-butadiene-styrene), and mineral filler (talc, dolomite, etc.). Coarse-grained surfacing and polymer films are used as protective layers.
Depending on the type of surfacing and application area, HYDROBASE FLEX is available in two grades:
HYDROBASE FLEX K – with coarse-grained surfacing on the top side and polymer film on the torch-applied side; used for installation of the upper layer of the roofing membrane;
HYDROBASE FLEX P – with polymer film on both sides of the sheet; used for installation of the lower layer of the roofing membrane and waterproofing of building structures (foundations, tunnels, etc.)
Transportation and Storage
Transportation is carried out by all types of transport in covered vehicles in accordance with the Cargo Transportation Rules applicable to the given type of transport. Throughout the entire storage period, the material must be protected from atmospheric precipitation. Rolls are stored vertically on pallets in a single row by height.
Packaging Information
The material is packaged in UV-stabilized film and supplied on pallets
Application Instructions
In accordance with SWEETONDALE Installation Instructions
Main characteristics
| Parameter name | HYDROBASE FLEX EPP | HYDROBASE FLEX EKP |
Test Method |
|||||
| Thickness, mm |
2.8 ± 0.2 |
3.8 ± 0.2 |
EN 1849-1 |
|||||
| Mass per unit area, kg/m²* (+0.25 kg) |
4,1 |
5,3 |
EN 1849-1 |
|||||
| Watertightness at 2 kPa pressure for 24 hours |
– |
No water penetration |
EN 1928 |
|||||
| Watertightness at 60 kPa pressure for 24 hours |
No water penetration |
– |
EN 1928 |
|||||
| Tensile strength, N, minimum
– longitudinal/transverse |
489/343 |
489/343 |
DSTU B V.2.7-83 |
|||||
| Flexibility on a bar with a radius of (25.0±0.2) mm at temperature, °C, maximum |
-20 |
-20 |
DSTU B V.2.7-83 |
|||||
| Flow resistance at elevated temperature, °C |
≥95 |
≥95 |
EN 1110 |
|||||
| Loss of coarse-grained surfacing, g/sample, maximum |
– |
1 |
DSTU B V.2.7-83 |
|||||
| Reaction to fire | Class E | DSTU EN 13501-1 | ||||||
| Type of protective coating:
upper side |
film without logo |
slate |
|
|||||
| torch-applied side |
film with logo |
film with logo |
|
|||||
| Length/width, m |
10×1 |
10×1 |
||||||
| Pallet packaging |
white heat-shrink bag with logo |
|||||||
*- the mass per 1 m² is provided for reference; the material is standardized by thickness. The manufacturer reserves the right to change this parameter;
TU U 22.2-32944149-012:2024
Thermal insulation boards made of extruded polystyrene foam
Product Description and Scope of Application
Extruded polystyrene foam CARBOLEX SOLID is a thermal insulation material with uniformly distributed closed cells. XPS CARBOLEX SOLID does not absorb water, does not swell, does not shrink, is chemically resistant and does not rot. High strength allows for a level and rigid base, which significantly extends the service life of the entire thermal insulation system. XPS CARBOLEX SOLID is used for thermal insulation of foundations, trafficked roofs, and floors with increased loads.
Transportation and Storage
The boards must be stored packaged and stacked on pallets separately by grades and sizes. Throughout the entire storage period, the material must be protected from atmospheric precipitation.
Packaging Information
The boards are packaged in UV-stabilized film.
Application Instructions
In accordance with SWEETONDALE Installation Instructions
|
Parameter |
Value |
Test Method |
| Compressive strength, kPa, not less than
50mm |
500 |
DSTU EN 826 |
| Tensile strength perpendicular to the board surface*, kPa |
100 |
DSTU EN 1607 |
| Declared thermal conductivity at 10°C, W/(m·K), not more than |
0,030 |
DSTU EN 12939 |
| Thermal conductivity, W/m*K λA λB |
0.034 |
DSTU B V.2.7-182 |
| Water absorption during long-term immersion, not more than, % |
0,4 |
DSTU B EN 12087 |
| Flammability |
G4 |
DBN V.1.1-7 |
| Operating temperature |
from -50 °C to +75 °C |
|
| Effective service life, years, not less than |
50 |
DSTU B V.2.7-182 |
*- tensile strength perpendicular to the face surfaces is determined for boards manufactured using the ThermoBonding method
Geometric parameters
|
Parameter |
Unit of measurement |
Value |
Test Method |
| Length |
mm |
1180 (±10) |
DSTU EN 822 |
| Width |
mm |
580 (±8) |
DSTU EN 822 |
| Thickness |
mm |
50 |
DSTU EN 822 |
| Edge type | L-edge | ||
| Thickness tolerance class | T1 | ||
TU U 22.2-32944149-012:2024
Thermal insulation boards made of extruded polystyrene foam
Product Description and Scope of Application
Extruded polystyrene foam CARBOLEX PROF features enhanced strength properties and is used for thermal insulation of foundations, floors, roofs, facades, and basements.
XPS CARBOLEX PROF contains graphite micro-particles that reflect thermal radiation and contribute to increasing the overall thermal resistance of the structure throughout the building’s service life
Transportation and Storage
The boards must be stored packaged and stacked on pallets separately by grades and sizes. Throughout the entire storage period, the material must be protected from atmospheric precipitation.
Packaging Information
The boards are packaged in UV-stabilized film.
Main physical and mechanical characteristics:
|
Parameter |
Value |
Test Method |
| Compressive strength, kPa, not less than
40mm 50mm 60mm and above |
230 250 250 |
DSTU EN 826 |
| Tensile strength perpendicular to the board surface*, kPa |
100 |
DSTU EN 1607 |
| Declared thermal conductivity at 10°C, W/(m·K), not more than |
0,032 |
DSTU EN 12939 |
| Water absorption during long-term immersion, not more than, % |
0,4 |
DSTU B EN 12087 |
| Reaction to fire |
Class F |
EN 13501-1+A1 |
| Operating temperature |
from -50 °C to +75 °C |
|
*- tensile strength perpendicular to facing surfaces is determined for boards manufactured using the ThermoBonding method
Geometric parameters:
|
Parameter |
Unit of measurement |
Value |
Test Method |
| Length |
mm |
1180 (±10) |
DSTU EN 822 |
| Width |
mm |
580 (±8) |
DSTU EN 822 |
| Thickness* |
mm |
40, 50, 60,100 |
DSTU EN 822 |
| Edge type | L-edge | ||
| Thickness tolerance class | T1 | ||
* – boards with thickness of 60 mm and above may be manufactured using the ThermoBonding method.
TU U 22.2-32944149-012:2024
Thermal insulation boards made of extruded polystyrene foam
Product Description and Scope of Application
XPS CARBOLEX ECO FAS is an insulation board made of extruded polystyrene foam with a special milled surface on both sides.
Extruded polystyrene foam CARBOLEX ECO FAS
specially designed for plastered facade structures and foundation insulation.
It can also be used for other structures where enhanced adhesion requirements are imposed on insulation boards to the substrate.
Transportation and Storage
The boards must be stored packaged and stacked on pallets separately by grades and sizes. Throughout the entire storage period, the material must be protected from atmospheric precipitation.
Packaging Information
The boards are packaged in UV-stabilized film.
Application Instructions
According to SWEETONDALE Installation Instructions https://sweetondale.cz/docs/instruktsii/
|
Parameter |
Value |
Test Method |
| Compressive strength, kPa, minimum
30 mm 40 mm 50 mm 60 mm and above |
150 150 200 200 |
DSTU EN 826 |
| Tensile strength perpendicular to the board surface*, kPa |
100 |
DSTU EN 1607 |
| Declared thermal conductivity at 10°C, W/(m·K), not more than |
0,033 |
DSTU EN 12939 |
| Thermal conductivity, W/m*K λA λB |
0.035 |
DSTU B V.2.7-182 |
| Water absorption during long-term immersion, not more than, % |
0,4 |
DSTU B EN 12087 |
| Flammability |
G4 |
DBN V.1.1-7 |
| Operating temperature |
from -50 °C to +75 °C |
|
| Effective service life, years, not less than |
50 |
DSTU B V.2.7-182 |
*- tensile strength perpendicular to the face surfaces is determined for boards manufactured using the ThermoBonding method
Geometric parameters:
|
Parameter |
Unit of measurement |
Value |
Test Method |
| Length |
mm |
1180 (±10) |
DSTU EN 822 |
| Width |
mm |
580 (±8) |
DSTU EN 822 |
| Thickness*, boards with L-edge |
mm |
30, 40, 50, 100 |
DSTU EN 822 |
| Thickness tolerance class | T1 | ||
* – boards with a thickness of 60 mm and above may be manufactured using the ThermoBonding method
TU U 22.2-32944149-012:2024
Thermal insulation boards made of extruded polystyrene foam
Product Description and Scope of Application
Extruded polystyrene foam CARBOLEX ECO is a thermal insulation material with uniformly distributed closed cells.
XPS CARBOLEX ECO does not absorb water, does not swell or shrink, is chemically resistant and not susceptible to rot.
High strength allows for a level and rigid base, which significantly extends the service life of the entire thermal insulation system.
XPS CARBOLEX ECO is used in cottage and low-rise construction for thermal insulation of foundations, roofs, floors, and facade insulation.
Transportation and Storage
The boards must be stored packaged and stacked on pallets separately by grades and sizes. Throughout the entire storage period, the material must be protected from atmospheric precipitation.
Packaging Information
The boards are packaged in UV-stabilized film.
Application Instructions
In accordance with SWEETONDALE Installation Instructions
| Parameter |
Value |
Test Method |
| Compressive strength, kPa, not less than
20 mm 30 mm 40 mm 50 mm 60 mm and above |
150 150 150 200 200 |
DSTU EN 826 |
| Tensile strength perpendicular to the board surface*, kPa |
100 |
DSTU EN 1607 |
| Declared thermal conductivity at 10°C, W/(m·K), not more than |
0,033 |
DSTU EN 12939 |
| Thermal conductivity, W/m*K λA λB |
0.035 |
DSTU B V.2.7-182 |
| Water absorption during long-term immersion, not more than, % |
0,4 |
DSTU B EN 12087 |
| Flammability |
G4 |
DBN V.1.1-7 |
| Operating temperature |
from -50 °C to +75 °C |
|
| Effective service life, years, not less than |
50 |
DSTU B V.2.7-182 |
*- tensile strength perpendicular to the facing surfaces is determined for boards manufactured using the ThermoBonding method
|
Parameter |
Unit of measurement |
Value, L-edge |
Value, straight edge |
Test Method |
| Length |
mm |
1180 (±10) |
1180 (±10) |
DSTU EN 822 |
| Width |
mm |
580 (±8) |
580 (±8) |
DSTU EN 822 |
| Thickness* |
mm |
30,40,50,100 |
20 |
DSTU EN 822 |
| Thickness tolerance class |
T1 |
|||
* – boards with a thickness of 60 mm and above may be manufactured using the ThermoBonding method
TU U V.2.7-23.9-35492904-006:2024
Thermal and acoustic insulation boards made of mineral wool
Product Description and Scope of Application
THERMOWOOL VENT EXTRA 75 FG is a non-combustible, hydrophobized thermal and sound insulation board made from mineral wool based on basalt group rock, with a single-sided fiberglass cloth coating.
THERMOWOOL VENT EXTRA 75 FG boards are designed for use in civil and industrial construction as single-layer thermal insulation or as an outer layer in double-layer thermal insulation in ventilated facade systems with an air gap. When using insulation with fiberglass cloth, a windproof membrane is not required.
Transportation and Storage
Transportation of boards is carried out in accordance with the requirements of DSTU B V.2.7-167. Boards are shipped to the consumer no earlier than 24 hours after storage at the warehouse. Boards must be stored packaged and stacked on pallets separately by grades and sizes. Throughout the entire storage period, the material must be protected from precipitation. The height of the board stack during storage must not exceed 3 m. Guaranteed storage period is 6 months from the date of manufacture.
Packaging Information
Polyethylene heat-shrink film is used for packaging. The wrapping method and fixation of the packaging material ensure reliable and durable packaging of the boards, protecting them during loading and unloading operations, transportation, and storage.
Application Instructions
In accordance with SWEETONDALE Installation Instructions
Main physical and mechanical characteristics:
|
Parameter |
Value |
Test Method |
| Density, kg/m3 |
75±7 |
DSTU B V.2.7-38 |
| Declared thermal conductivity at 10°C, W/(m·K), not more than |
0,035 |
DSTU B EN 12667 |
| Thermal conductivity, W/m*K λA λB |
0.039 |
DSTU B V.2.7-182 |
| Compressive stress at 10% linear deformation, kPa, not less than |
10 |
DSTU EN 826 |
| Tensile strength in the direction perpendicular to the board plane, kPa, not less than |
5 |
DSTU EN 1607 |
| Long-term water absorption, kg/m2, not more than |
3 |
EN 12087 |
| Short-term water absorption, kg/m2, not more than |
1 |
EN 1609 |
| Reaction to fire |
A1 |
DSTU EN 13501-1 |
| Combustibility class |
NG |
DBN V.1.1-7 |
| Effective service life, years, not less than |
50 |
DSTU B V.2.7-182 |
Geometric parameters:
|
Parameter |
Unit of measurement |
Value |
Test Method |
| Length |
mm |
1200 |
DSTU EN 822 |
| Width |
mm |
600 |
DSTU EN 822 |
| Thickness (in 10 mm increments) |
mm |
50–200 |
DSTU EN 823 |
| Tolerance limits length / width |
mm |
±2 / ±1.5% |
DSTU EN 13162 |
| Thickness tolerance class | T4 | ||
Logistics parameters:
| Length, mm | 1200 | 1200 |
| Width, mm | 600 | 600 |
| Thickness, mm50100 | ||
| Quantity per package, boards, pcs | 6 | 3 |
| Quantity per package, m2 | 4.32 | 2.16 |
| Quantity per package, m3 | 0.216 | 0.216 |
| Quantity per pallet, packages, pcs | 32 | 32 |
| Quantity per pallet, m3 | 6.912 | 6.912 |
| Loading capacity per vehicle, volume, m3 | 76.032 | 76.032 |